Tascam PORTASTUDIO 788 Bedienungsanleitung PDF herunterladen (Seite 20)

Built-In Effect Processing TASCAM 788 Operational Tutorial • 8/2000 Edition

ROUTING EFFECTS

Section IV

Built-in Effect Processing

Associating EFFECT 1 to an input:

When EFFECT 1 is being used as a Multi-Effect

Processor, it is assigned to an insert on a channel on

the main mixer. If you are recording multiple tracks

with the same processing, you may want to "associate"

the processor with an input by pressing EFFECT 1 and

INPUT (A, B, C or D). This will automatically move

EFFECT 1 through the mixer with the associated input.

This will save a lot of routing during the recording

process. Keep in mind that this only works if the input

is assigned to one channel only, and it will disengage

if the input is assigned to the submixer.

Assigning effect routing can be done totally from the

surface of the 788. Simply press the button of the effect

processor, and the button for the destination. (The source

and destination buttons must be pressed simultaneously.)

This routing

technique means

that you don't

have to dig through

menus to route

effects. It's all on

the surface of the

788 itself. The

specific button

pushes for each

set-up are shown in

the chart above to

the right. Refer to

it for specific button

combinations.

To assign EFFECT 2 as a Stereo Dynamic Processor,

Press EFFECT 2 and STEREO simultaneously.

Routing on the 788 as a whole is done by pressing

the buttons for the source and destination at the

same time, just like you were plugging in a cable.

STEREO EFFECT PROCESSOR

Stereo Effect Processor on EFFECT SEND:

To assign EFFECT 1 in this configuration,

press EFFECT 1 and SEND simultaneously.

DISTORTION NOISE GATE FLANGER DELAYCOMPRESSOR

Multi-Effect Processor inserted into a

specific main mixer CHANNEL: To assign

EFFECT 1 in this configuration, press

EFFECT 1 and SELECT for the channel

you want the chain inserted to.

Multi-Effect Processor assigned to follow

an input: To assign EFFECT 1 to follow

the routing of the input, press EFFECT 1

and INPUT (A, B, C, or D). This will

keep the processing chained with the

input through any channel assignment

on the main mixer. This only works on

one channel at a time, and will not work

if the input is assigned to the submixer.

EFFECT 1

STEREO DYNAMICS PROCESSOR

THRESHOLD

ATTACK

GAIN

RATIO

THRESHOLD

ATTACK

GAIN

RATIO

THRESHOLD

ATTACK

GAIN

RATIO

THRESHOLD

ATTACK

GAIN

RATIO

THRESHOLD

ATTACK

GAIN

RATIO

THRESHOLD

ATTACK

GAIN

RATIO

THRESHOLD

ATTACK

GAIN

RATIO

STEREO EFFECT PROCESSOR

Stereo Effect Processor on AUX SEND:

To assign EFFECT 2 in this configuration,

press EFFECT 2 and SEND simultaneously.

Stereo Dynamics Processor on the

STEREO BUSS: To assign EFFECT 2 in

this configuration, press EFFECT 2 and

STEREO simultaneously.

Dynamic Processors on all eight mixer

channels: To assign EFFECT 2 in this

configuration, press EFFECT 2 and any

channel SELECT button.

EFFECT 2

The 788 has two built-in effect processing engines,

EFFECT 1 and EFFECT 2. These processors are completely

independent of each other, and each can be used in a

variety of ways.

EFFECT 1 can be assigned as either a single stereo effect

processor on the EFFECT SEND, or it can function as a

multieffect processor inserted on a single channel.

EFFECT 2 can be assigned as either a single stereo effect

processor on the AUX SEND, a single stereo dynamics

processor on the stereo buss, or a multichannel dynamics

processor with separate dynamics processing for each

channel on the main mixer.

Separate preset libraries are kept for each type of effect

processing, so you don't have to worry about writing over

your favorite guitar preset with the stereo dynamic

settings you need.

The effect programs can be recalled by MIDI, so you can

use the processors in automated mixdown, or even in a

live show. For guitar players, you can use a MIDI pedal

board to recall your effect patches inside the 788. For

keyboard players, you can recall effects with controller

keyboards and synths. In the studio environment, most

standard MIDI sequencers can send program change

messages to change the presets.

EFFECT OVERVIEW

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 32 33

Kommentare zu diesen Handbüchern

Keine Kommentare

Tascam PORTASTUDIO 788 Bedienungsanleitung Seite 20

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Musikausrüstung Tascam PORTASTUDIO 788